ENCORE WIRELESS BRIDGE ENRXWI-G

	Free SHIPPING on everything

   Home
   FTA Receivers
   8psk Modules
   Hard Drives
   Networking
   Dishes
   LNBs
   Switches
   Motors
   Remotes
   Data Cables
   RG6 Cables
   LNB Holders
   UHF Kits
   Card Readers
   Signal Finders
   Accessories
Linkbox

   Shipping
   Contact Us
   Channel List
   RMA Request
   Return Policy
   Warranty
What Is Free To Air?

ENCORE WIRELESS BRIDGE ENRXWI-G

Price: $59.99 each
Buy 5 to 9 $55.00 each
Buy 10 or more $50.00 each

KEY FEATURES

Features 3 Operation Modes: Extender (or Repeater), Access Point and Access Point Client

Increases the coverage area of 802.11b/g wireless networks in Extender Mode without additional wiring

Features strong wireless security: WEP, WPA, WPA-PSK, WPA2 and WPA-PSK2

Features web-based configuration tool

Backward compatible with 802.11b/g

Encore Wireless LAN Extender is a multifunctional wireless device. It functions in three modes: Extender*, Access Point and Access Point Client. The Extender mode offers a simple and cost-effective way to expand the coverage area of your current 802.11b/g wireless network.

Extender Mode
Place ENRXWI-G within the range of your current wireless network. Subsequently, ENRXWI-G can pickup signal from the wireless router (or access point) and transfer the signal further away than the original coverage area. You have thus effectively extended your wireless network without wiring or complicated configuration. Also, you can improve the reception at dead spots, areas characterized by poor signal quality, by placing ENRXWI-G between the dead spots and the wireless router.

Access Point Mode
Connect ENRXWI-G to your wired Ethernet router (using a RJ-45 cable). Configure ENRXWI-G accordingly. Now, you have just upgraded your old wired router into an 802.11g wireless router.

Access Point Client Mode
Connect ENRXWI-G to the Ethernet port of you desktop or laptop computer (using a RJ-45 cable). Configure ENRXWI-G accordingly. Now, you can use it like a regular 802.11g wireless adapter enabling your computer to access wireless network.

Use ENRXWI-G, in Extender Mode, to increase your wireless coverage over an extended area such as in a warehouse, multi-story house and public space. You can also use it in wireless hot spot or outdoors where you always need additional coverage for your wireless network. Encore Wireless LAN Extender operates both in 802.11b and 802.11g standards. For your protection and convenience, ENRXWI-G comes with strong security features such as WPA-PSK, WPA2 and web-based configuration utility.

SPECIFICATIONS

Standard: IEEE 802.11b/g (Wireless LAN)
IEEE 802.3u (Fast Ethernet)
Radio Technology: 802.11b: Direct Sequence Spread Spectrum (DSSS)
802.11g: Orthogonal Frequency Division Multiplexing (OFDM)
Transmission Rate: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54Mbps (auto sense)
Receiver Sensitivity: 54Mbps: Typical -68dBm @ 10% PER (Packet Error Rate)
11Mbps: Typical -78dBm @ 8% PER (Packet Error Rate)
Wireless LAN Frequency Range: 2412 ~ 2484 MHz ISM band (channels 1 ~ 14)
Modulation Schemes: DBPSK/DQPSK/CCK/OFDM
Media Access Protocol: CSMA/CA with ACK
Transmit Power: 802.11g: Typical 15dBm
802.11b: Typical 18dBm
Antenna Type: One external 2dB dipole antenna
Interface: 10/100BASE-TX RJ-45 Ethernet
Channel: USA: 1 ~ 11
Europe: 1 ~ 13
Japan: 1 ~ 14 :
Security: 64/128-bits WEP Encryption/Decryption
WPA
WPA2
WPA-PSK
WPA2-PSK
Range Coverage: Indoor: Up to 50 meters (depends on environment)
Outdoor: Up to 100 meters (depends on environment)
Diagnostic LEDs: Power; LAN: Link, ACT; WLAN: ACT
Power Adapter: 7.5V / 1A
Operation Temperature: 0 ~ 40°C
Storage Temperature: -25 ~ 70 °C
Humidity: 10% ~ 90% RH, no condensation
Certifications: FCC Part 15.247 for US
ETS 300 328 for Europe

Shipping - Contact Us - Return Policy - Warranty - RMA Request